Page 1 of 1
MadMapper & Moving Heads
Posted: Tue May 12, 2015 10:39 am
by CaseyJScalf
Officially MadMapper can do basic colors for DMX fixtures.
What is the best way to run a light show with MM and moving heads?
Do most of you run separate software? Some middleware to reinterpret color values as other channels?
Looking to chat about best-of methods for this as trying to mix in 3+ programs gets cumbersome.
Re: MadMapper & Moving Heads
Posted: Tue May 12, 2015 6:28 pm
by sigmasix
On our side we made a module in modul8 to control moving heads and we use mad mapper only with LED stuff or old school dimming lights.
Re: MadMapper & Moving Heads
Posted: Tue May 12, 2015 10:51 pm
by CaseyJScalf
Thanks for the reply. So I was not aware that Modul8 could do that. Custom plugin?
Either way, trying to iron out the workflow for live shows with these.
Could it be possible to make a custom fixture type in MM that translated color values to movements? Maybe with some smoothing so that the movements were not as erratic as the color values?
Re: MadMapper & Moving Heads
Posted: Wed May 13, 2015 11:51 am
by Xaver2k
Hey on my last show i controlled some scanners with madmapper. it was a very basic function i just took some lines and made it fading then i putted the dmx channel for the movements and dimmers on top... so very basic ^^ but it was only 2 scanner and an easy side effect
@sigmasix
can you pls tell us more about your plugin? a small video? this sounds really interesting!
Re: MadMapper & Moving Heads
Posted: Wed May 13, 2015 10:10 pm
by CaseyJScalf
Xaver2k,
So it sounds like you can re-route color values to movements?
Re: MadMapper & Moving Heads
Posted: Sun May 17, 2015 5:18 am
by CaseyJScalf
I will have to get some simple moving heads and try this out!
http://www.amazon.com/Chauvet-SlimPAR-56-CHAUVET/dp/B003H3JKX0I love the Chauvet PAR cans, any suggestions on a simple moving head to interface with?
Re: MadMapper & Moving Heads
Posted: Sun May 17, 2015 9:25 pm
by Xaver2k
yes you can set the brightness of a Stripe to a DMX value
Re: MadMapper & Moving Heads
Posted: Mon May 18, 2015 12:50 am
by CaseyJScalf
Excellent, looking forward to more experimentation!
Re: MadMapper & Moving Heads
Posted: Sun May 24, 2015 10:53 pm
by franz
it is very easy to control moving heads with mad mapper.
make a custom fixture, with the right amount of DMX channels (some moving lights can use up to 20 channels or more),
then set the channels to custom/ slider, this way you can have a precise control of what data you send (without being linked to the underlying pixels data)
Re: MadMapper & Moving Heads
Posted: Tue May 26, 2015 10:43 pm
by CaseyJScalf
Thank you Franz. I look forward to trying it out.
As I am sure you have played around with MM and some moving heads before, can you recommend a basic model to get started with?
I think this may really open up a lot of doors for stage designs. I really appreciate having all of the elements under unified control. Thank you for the tips!
Re: MadMapper & Moving Heads
Posted: Fri May 29, 2015 3:26 pm
by franz
Any Martin MAC will do the job.
The MAC 700 is a very common, cheap model, easy to rent
Re: MadMapper & Moving Heads
Posted: Thu Apr 28, 2022 4:01 pm
by bjmstudio
it is very easy to control moving heads with mad mapper.
make a custom fixture, with the right amount of DMX channels (some moving lights can use up to 20 channels or more),
then set the channels to custom/ slider, this way you can have a precise control of what data you send (without being linked to the underlying pixels data)
Hi franz,
I'm very new with madmapper. I want to control Pixel LED and a Moving Head at the same time. How can I re-route the light signal
to a DMX Channel for Pan/ Tilt etc.?
thx for help!
Re: MadMapper & Moving Heads
Posted: Wed May 04, 2022 12:52 pm
by franz
you'd have to create a custom moving head dmx fixture, where PAN -> R, TILT-> G, FOCUS-> B, for instance.
Note that instead of sampling RGB data from a texture, you could set some sliders and animate them with cues.