garageCube

there wasx a bug, it is now fixed in beta 2, thanks for reporting Thanks. In Beta 2 ,I can now see the values for a large number of Mediapipe values and triggers, so for example I can change a Quad's Opacity by how much my head is rotated or how big my smile is as a control. What I want to do is ta...

When I add the Mediapipe module in MM and go to Setup inside the module I get "No Camera Frames yet" and most of the Parameter UI does nothing. I set the camera to "Integrated Camera" and the camera is working in the rest of MM. I get face_landmarker.task not found or pose_landmarker.task not found ...

If you are looking for inspiration when writing MadAI prompts then add some of these verbs and nouns into the mix. If you have other good ones (that are non obvious) then add as comment! 3D Aberrate Animate Anti-alias Audio Enable Axis Background Beams Blur Bounce Camera Caustic Centre Chromatic Clo...

So I have worked out how to do it (its now in the public library as "Swipe left right"). I will use this with WS2811 Pixel strings and drive the variable "Swipe" from Audio/Oscillator or an Arduino Potentiometer knob. Obviously you can make it go up/down by rotating the quad!

I have an Enttec OpenDMX to send DMX out to a set of Par Cans. I also have an Enttec Pixel Octo to send DMX out to a LED Pixel string via ArtNet. It looks as if there is only drop down option for DMX output destination. Is it possible to use both DMX via USB and DMX via ArtNet or is it one or the ot...

I have 3 Helios DACs and they are cheap and all work flawlessly

I use "Remote Desktop" where a thin client device is connected close to a set of ILDA cabled Lasers and publishes a private wifi SSID (no internet required), so it works for Madlaser but not for a connected projector. I spent ages trying to work out if there was a way to get a copy of MM on the thin...

I am looking for a simple "fill and empty" material (see attachment) that just fills a solid colour from bottom to top and back to the bottom. The speed with which it fills and empties as well as the colour should be controllable. I am sure it is simple to code, but I am not a programmer and I could...

The Ponk software for TouchDesigner is at https://github.com/madmappersoftware/Ponk but I can't work out how you install it!

What is the lowest cost way to connect my PC to my WS2811 string? (I can't get Teensy to work) I need some box that takes Ethernet (I assume ArtNet only works on Ethernet in and lets me connect the 3 wires from my LED string. Does such a device exist? I want the equivalent of the Enttec Open USB/DMX...

An even better method was to create a private WiFi network (to avoid long runs of Ethernet cable). The Thin client device is positioned close to the lasers (connected on ILDA cables) and broadcasts a private SSID which your main PC connects to it via WiFi (no need for Internet access). It automatica...

I was experimenting with writing Lua code in the Controls Container module (where you take up to 3 inputs and perform maths on them and create a new output variable. I am not a programmer, so I tried using Bing Chat to write the code for me. It worked well! I typed the following into Bing Chat "writ...

I have used TOUCHOSC app (on Android phone) to either send pre-composed messages (say where you know the song titles in advance) to Mad Laser or use the virtual keyboard to enter and send new strings via OSC protocol.

What is the best way to display a long text message on a low speed laser (for example credits at the end of a show). I want to scroll the text to avoid jitter, but the Laser Text Generator only displays a few characters and then starts back at the beginning. Is there some way to scroll a lot of text?

I tried various Fixture settings and briefly managed to get all 25 lights firing (right pattern but wrong colours - first 4 lights white the rest Red) by using Garagecube SFX-01 W 1m with Pixel width of 75 and Pixel size of 1 and Pixel type L. I now can't reproduce that working so its seems very fra...